DetailsMaxim

sorensen DLM 5-350E Programmable DC Power Supply 5V 350A 1750W

sorensen DLM 5-350E Programmable DC Power Supply 5V 350A 1750W is designed to provide highly stable, continuously variable output voltage and current for a broad range of applications in a compact 2U (3½“ high) chassis.

The 4 kW power rating is new to the Sorensen Family of power supplies. Both the 3 kW and 4 kW models have output voltages from 0-5 VDC to 0-600 VDC and a current range from 0-5A to 0-450A. The output RMS noise is as low as 10 mV. The output will recover to 1% of its steady-state voltage within 1 ms for a step load change of 100% to 70% or 70% to 100%. The front panel layout makes the series extremely easy to use. Control switches include: power on, enable/ standby and local/remote.

Displays and indicators show programmed set points and operational control status. The programmed voltage, current and overvoltage set points are displayed with two large 3½ digit LED displays. Operational Status LEDs indicate power on, shutdown, overtemperature, overvoltage, constant current and voltage mode status. Control Status LEDs indicate front panel lockout, remote control and standby status. IEEE-488.2 controls LEDs indicate error, service request and remote address status.

The 3 kW Models will accept 200*/230 VAC single phase and 200*/208 VAC three phase input power.

The 4 kW Models will accept 200*/208 VAC, three phase or optional 400 or 480 VAC three phase input power.

*Operating temperature below 40°C

Quantity:

Feature Specification

High Power Density : 3 kW and 4 kW models, 2U (3½“high), (19“ wide); no top or bottom clearance spacing required
Preview Push-button : Overvoltage protection (OVP), voltage and current preview buttons
Remote Voltage Sense : Sense leads are easily connected to a solder less connector
Parallel or Series Operation Field configurable
Power Factor Correction ‰¥0.98 1 Ð¤ 3kW

Common
Front Panel Controls	Knobs with 3½ digit digital displays to control output voltage and current settings. Power on/off switch, output enable/standby switch and local/remote switch. Voltage, current and overvoltage preview push buttons allow you to preview the programmed settings at any time; overvoltage limit is adjusted with a set screw accessible through the front panel.
Displays and Indicators	Voltage and overvoltage setting 3½ digit LED display, current setting 3½ digit LED display. LED indicators for power on, shutdown, remote, overvoltage protection, overtemperature and front panel lockout, constant voltage and constant current modes. IEEE-488.2 indicators include error, SRQ and address (M9E option).
Built-in Protection	Output overvoltage (resets by cycling the enable/standby switch), overtemperature (will automatically reset)
Input
Voltage and Frequency 3 kW	180-264 VAC, 47-63 Hz, single or three phase (<200 VAC range limited to 40°C maximum)
4 kW	180-264 VAC, 47-63 Hz, three phase (<200 VAC range limited to 40°C maximum)
Power Factor	0.95 typical with three phase input, 0.98 typical with single phase input
Current	3 kW: single phase, 21A RMS; three phase, 12A RMS 4 kW: 180-264 VAC, 15A RMS; 345-455 VAC, 8.5A RMS; 432-528 VAC, 6.5A RMS;
Output
Regulation	Line: For input voltage variation over the AC input voltage range, with constant rated load. Load: For 0-100% load variation, with constant nominal line voltage. Voltage: 0.05% of maximum rated output +2mV Current: 0.1% of maximum rated output
Transient Response	Typically recovers in 1.5 ms to within 1% of steady-state output voltage (greater than 50% of Vmax) for 70-100% or 100-70% load change.
Stability	±0.05% of maximum voltage or current over 8 hours after 15 minute warm-up time at fixed line, load and temperature. Current accuracy for 5V, 8V, and 16V models is 1% typical.
Efficiency	5-8V Models: 82% typical 16-80V Models: 87% typical 150-600V Models: 85% typical (at maximum output power)
Temperature Coefficient	0.02%/°C of rated output voltage; 0.03%/°C of rated output current. Change in output per °C change in ambient temperature, with constant line and load.
Weight & Shipping Weight
Weight	40 lbs. (18.2 kg)
Shipping Weight	49 lbs. (22.3 kg)
Physical
Height	3-1/2“ (88 mm)
Width	19“ (482 mm)
Depth	18“ (508 mm)
Environmental
Operating Temperature	0°C to 50°C, no derating (<200 VAC range limited to 40°C maximum)
Storage Temperature	-40°C to 65°C
Cooling	Internal fans with overtemperature protection
Output
Model	Preview Accuracy	OVP Adjustment Range (5% to 110% of Vmax)
Voltage (0.05% of Vmax +1 count)	Current ( 1.0% of Imax +1 count)
DLM 5-350E	0.04V	5A	0.3-5.5V
DLM 5-450E	0.04V	6A	0.3-5.5V
DLM 8-350E	0.05V	5A	0.4-8.8V
DLM 8-450E	0.05V	6A	0.4-8.8V
DLM 16-185E	0.09V	3A	0.8-17.6V
DLM 16-250E	0.09V	4A	0.8-17.6V
DLM 32-95E	0.3V	1.1A	1.6-35V
DLM 32-125E	0.3V	1.4A	1.6-35V
DLM 40-75E	0.3V	0.9A	2-44V
DLM 40-100E	0.3V	1.1A	2-44V
DLM 60-50E	0.4V	0.6A	3-66V
DLM 60-66E	0.4V	0.8A	3-66V
DLM 80-37E	0.5V	0.5A	4-88V
DLM 80-50E	0.5V	0.6A	4-88V
DLM 150-20E	0.9V	0.3A	7.5-165V
DLM 150-26E	0.9V	0.4A	7.5-165V
DLM 300-10E	1.6V	0.11A	15-330V
DLM 300-13E	1.6V	0.14A	15-330V
DLM 600-5E	3.1V	0.06A	30-660V
DLM 600-6.6E	3.1V	008A	30-660V
Output
Model	Ripple and Noise
Ripple (RMS)*	Noise (P-P)
DLM 5-350E	12mV	100mV
DLM 5-450E	12mV	100mV
DLM 8-350E	12mV	100mV
DLM 8-450E	12mV	100mV
DLM 16-185E	10mV	100mV
DLM 16-250E	10mV	100mV
DLM 32-95E	10mV	100mV
DLM 32-125E	10mV	100mV
DLM 40-75E	10mV	100mV
DLM 40-100E	10mV	100mV
DLM 60-50E	15mV	100mV
DLM 60-66E	15mV	100mV
DLM 80-37E	15mV	120mV
DLM 80-50E	15mV	120mV
DLM 150-20E	30mV	200mV
DLM 150-26E	30mV	200mV
DLM 300-10E	60mV	300mV
DLM 300-13E	60mV	300mV
DLM 600-5E	100mV	500mV
DLM 600-6.6E	100mV	500mV
* RMS ripple typical from 20 Hz to 300 kHz Specifications subject to change.
Output
Model	Stability
Voltage (0.05% of Vmax)	Current (0.05% of Imax)
DLM 5-350E	3 mV	175 mA
DLM 5-450E	3 mV	225 mA
DLM 8-350E	4 mV	175 mA
DLM 8-450E	4 mV	225 mA
DLM 16-185E	5 mV	93 mA
DLM 16-250E	5 mV	125 mA
DLM 32-95E	16 mV	48 mA
DLM 32-125E	16 mV	63 mA
DLM 40-75E	20 mV	38 mA
DLM 40-100E	20 mV	50 mA
DLM 60-50E	30 mV	25 mA
DLM 60-66E	30 mV	33 mA
DLM 80-37E	40 mV	19 mA
DLM 80-50E	40 mV	25 mA
DLM 150-20E	75 mV	10 mA
DLM 150-26E	75 mV	13 mA
DLM 300-10E	150 mV	5 mA
DLM 300-13E	150 mV	6.5 mA
DLM 600-5E	300 mV	2.5 mA
DLM 600-6.6E	300 mV	3.3 mA
Output
Model	Output Rating
Voltage (VDC)	Current (ADC)
DLM 5-350E	0-5	0-350
DLM 5-450E	0-5	0-450
DLM 8-350E	0-8	0-350
DLM 8-450E	0-8	0-450
DLM 16-185E	0-16	0-185
DLM 16-250E	0-16	0-25
DLM 32-95E	0-32	0-95
DLM 32-125E	0-32	0-125
DLM 40-75E	0-40	0-75
DLM 40-100E	0-40	0-100
DLM 60-50E	0-60	0-50
DLM 60-66E	0-60	0-66
DLM 80-37E	0-80	0-37
DLM 80-50E	0-80	0-50
DLM 150-20E	0-150	0-20
DLM 150-26E	0-150	0-26
DLM 300-10E	0-300	0-10
DLM 300-13E	0-300	0-13
DLM 600-5E	0-600	0-5
DLM 600-6.6E	0-600	0-6.6
Output
Model	Regulation Line and Load
Voltage (0.05% of Vmax + 2mV)	Current (0.1% of Imax)
DLM 5-350E	5 mV	350 mA
DLM 5-450E	5 mV	450 mA
DLM 8-350E	6 mV	350 mA
DLM 8-450E	6 mV	450 mA
DLM 16-185E	10 mV	185 mA
DLM 16-250E	10 mV	250 mA
DLM 32-95E	18 mV	95 mA
DLM 32-125E	18 mV	125 mA
DLM 40-75E	22 mV	75 mA
DLM 40-100E	22 mV	100 mA
DLM 60-50E	32 mV	50 mA
DLM 60-66E	32 mV	66 mA
DLM 80-37E	42 mV	37 mA
DLM 80-50E	42 mV	50 mA
DLM 150-20E	77 mV	20 mA
DLM 150-26E	77 mV	26 mA
DLM 300-10E	152 mV	10 mA
DLM 300-13E	152 mV	13 mA
DLM 600-5E	302 mV	55 mA
DLM 600-6.6E	302 mV	7 mA
Output
Model	Meter Accuracy
Voltage (0.5% of Vmax + 1 Count)	Current (0.75% of Imax + 1 Count)
DLM 5-350E	0.04 V	4 A
DLM 5-450E	0.04 V	5 A
DLM 8-350E	0.05 V	4 A
DLM 8-450E	0.05 V	5 A
DLM 16-185E	0.09 V	3 A
DLM 16-250E	0.09 V	3 A
DLM 32-95E	0.3 V	0.8 A
DLM 32-125E	0.3 V	1 A
DLM 40-75E	0.3 V	0.7 A
DLM 40-100E	0.3 V	0.9 A
DLM 60-50E	0.4 V	0.5 A
DLM 60-66E	0.4 V	0.6 A
DLM 80-37E	0.5 V	0.4 A
DLM 80-50E	0.5 V	0.5 A
DLM 150-20E	0.9 V	0.3 A
DLM 150-26E	0.9 V	0.3 A
DLM 300-10E	1.6 V	0.09 A
DLM 300-13E	1.6 V	0.11 A
DLM 600-5E	3.1 V	0.05 A
DLM 600-6.6E	3.1 V	0.06 A
Rear Panel Control/Monitor
Remote Sense	The maximum total allowed sense line drop is 2V for 5V, 8V and 16V models and 5V for all other models. Line drop subtracts from the maximum available output voltage at full rated power.
Remote Sense Protection	Unit will not be damaged due to misconnection of the remote sense leads.
Remote Programming	Voltage, current (0-100%) and OVP (5-110%) of full scale can be programmed by selectable 0-5 VDC, 0-10 VDC, or 0-5 kÎ©.
Remote Monitoring	Voltage or current can be monitored with user-selectable ranges, 0-5 VDC or 0-10 VDC
Operational Features	Master/slave parallel* operation, up to 2 units can be connected in parallel with active current sharing control to within 10% of each supply. Series operation, up to 3 units of the same model type can be connected in series (consult manual). Negative terminal rated at 150 Vmax above ground
Software	LabVIEW® drive"