|
POWER (fundamental), CW, @ OUTPUT CONNECTOR
|
|
Nominal
|
45 watts
|
|
Minimum
|
40 watts
|
|
Linear @ 1dB Compression
|
10 watts minimum
|
|
FLATNESS
|
±8 dB maximum
|
|
FREQUENCY RESPONSE
|
18-26.5 GHz instantaneously
|
|
INPUT FOR RATED OUTPUT
|
1.0 milliwatt maximum
|
|
GAIN (at maximum setting)
|
46 dB minimum
|
|
GAIN ADJUSTMENT (continuous range)
|
35 dB minimum
|
|
INPUT IMPEDANCE
|
50 ohms, VSWR 2.0:1 maximum
|
|
OUTPUT IMPEDANCE
|
50 ohms, VSWR 2.5:1 typical
|
|
MISMATCH TOLERANCE
|
Output power foldback protection at reflected power exceeding 10 watts. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. May oscillate with unshielded open due to coupling to input. Should not be tested with connector off.
|
|
MODULATION CAPABILITY
|
Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal. AM peak envelope power limited to specified power.
|
|
VIDEO PULSE CAPABILITY (S2V OPTION)
|
|
Pulse Width:
|
0.1 microseconds min
|
|
Pulse Rate (PRF):
|
10 kHz max
|
|
Duty Cycle:
|
Some restrictions apply. Contact AR with application requirements.
|
|
RF Rise and Fall:
|
100 ns max (10% to 90%)
|
|
Delay:
|
500 ns max from pulse input to RF 90%
|
|
Pulse width distortion:
|
200 ns max (50% points of output pulse width compared to 50% points of input pulse width)
|
|
Noise Power Density, (pulse off):
|
Minus 140 dBm/Hz (typical)
|
|
Pulse Off Isolation:
|
80 dB minimum, 90 dB typical
|
|
Pulse Input:
|
TTL Level, 50 Ohm nominal termination, high level enables RF when video pulsing mode is selected.
|
|
NOISE POWER DENSITY
|
Minus 60 dBm/Hz (maximum)
Minus 65 dBm/Hz (typical)
|
|
HARMONIC DISTORTION
|
Minus 20 dBc maximum
Minus 28 dBc typical
|
|
PRIMARY POWER
|
99-260 VAC
50/60 Hz single phase
850 VA maximum
|
|
CONNECTORS
|
|
RF input
|
Type K female on rear panel
|
|
RF output
|
Type WR-42 waveguide flange on rear panel
|
|
RF output sample port
|
Type K female on rear panel
|
|
Pulse input (S2V option)
|
Type BNC female or rear panel
|
|
GPIB
|
IEEE-488 on rear panel
|
|
Interlock
|
DB-15 female on rear panel
|
|
COOLING
|
Forced air (self contained fans), air entry and exit in rear.
|
|
SIZE (W x H x D)
|
50.3 x 16.5 x 68.6 cm, 19.8 x 6.5 x 27 in.
|
|
WEIGHT (approximate)
|
30 kg, 65 lbs.
|
![](javascript:addcart({"pid":914,"pname":"Rohde & Schwarz BBA150-series Broadband Amplifiers 4 kHz - 6 GHz up to 3000W","image":"/uploads/2019/04/rs_bba150.png"})){kind=link}
![](javascript:addcart({"pid":913,"pname":"Rohde & Schwarz BBA130-series Broadband Amplifiers 80 MHz - 6 GHz up to 4200W","image":"/uploads/2019/04/rs_bba130.png"})){kind=link}
![](javascript:addcart({"pid":1416,"pname":"Teseq CBA 6G-120B Broadband Amplifier 1.8 GHz - 6 GHz 120W","image":"/uploads/2018/01/teseq_cba_6g-120b.png"})){kind=link}
![](javascript:addcart({"pid":1415,"pname":"Teseq CBA 6G-080B Broadband Amplifier 1.8 GHz - 6 GHz 80W","image":"/uploads/2018/01/teseq_cba_6g-080b.png"})){kind=link}
![](javascript:addcart({"pid":1414,"pname":"Teseq CBA 6G-040B Broadband Amplifier 1.8 GHz - 6 GHz 40W","image":"/uploads/2018/01/teseq_cba_6g-040b.png"})){kind=link}
![](javascript:addcart({"pid":1413,"pname":"Teseq CBA 3G-500B Broadband Amplifier 800 MHz - 3.1 GHz 500W","image":"/uploads/2018/01/Image_Placeholder.png"})){kind=link}
![](javascript:addcart({"pid":1412,"pname":"Teseq CBA 3G-300B Broadband Amplifier 800 MHz - 3.1 GHz 300W","image":"/uploads/2018/01/teseq_cba_3g-300b.png"})){kind=link}
![](javascript:addcart({"pid":1411,"pname":"Teseq CBA 3G-100B Broadband Amplifier 800 MHz - 3.1 GHz 100W","image":"/uploads/2018/01/teseq_cba_3g-100b.png"})){kind=link}
![](javascript:addcart({"pid":1410,"pname":"Teseq CBA 3G-050B Broadband Amplifier 800 MHz - 3.1 GHz 50W","image":"/uploads/2018/01/Teseq_cba_3g-050b.png"})){kind=link}