| Performance |
| Specification typical at 25°C ambient. Unless otherwise noted; testing was done in Current mode with a load = 500 μH +100 mΩ |
| Peak Current Limit |
209 A |
| Gain Linearity
(over input signal, from 0.2V to 5V) |
DC |
0.0125% |
| AC |
0.030% |
| Output Offset (adjustable to zero) |
Voltage Mode |
Less than ±400 μV |
| Current Mode |
±5 mA |
| Input Characteristics |
Three-Terminal Barrier Block Connector |
Balanced with ground; 20 kΩ differential |
| BNC Connector |
Unbalanced; 10 kΩ single ended |
| Max Input Voltage |
± 10 V balanced or unbalanced |
| Common Mode Rejection |
-58 dB with 5 V input |
| Output Impedance |
Current Mode (effective) |
2000 Ω |
| Voltage Mode (typical) |
3 mOhm in Series with 2.23 μH |
| Load |
Current Mode |
500 μH + 100 mΩ |
| Adaptable Range |
5 μH to 2.5 H, 0.01 Ω to 20 Ω |
| Current Mode Response |
-3 dB at 5 kHz (compensation dependent) |
| Current Settling Time |
Ramp 0 A to ±50 A or ±50 to 0 A |
20 μs to within 1.0 A or 1% |
| 35 μs to within 200 mA, 0.2% |
| Total Harmonic Distortion |
Current Mode |
Less than 0.1% |
| Load |
500 μH + 100 mΩ |
| Noise Floor (when Blanking circuit is enabled) |
5 μA or less |
| DC Drift |
Self-Heating Drift, 0 to ±60 A |
| 5 mA/10 minutes maximum |
| Noise Output |
10 Hz to 1 kHz |
0.2 mA |
| 1 kHz to 60 kHz |
0.05 mA |
| Ripple Noise Output |
None |
| Slew Rate, Voltage Mode |
41 V/μs |
| Remote Control and Monitoring
(back-panel D connector) |
Current Monitor |
± 1 V / 20 A ± 1% |
| Reporting |
System Fault, Over Temp, Over Voltage, Over Load |
| Control |
Force to Standby, Remove from Standby, Reset after a Fault |
| Amplifier Protection |
Over Load/Distortion (IOC) |
Shutdown or clipped output |
| Current vs Time (ODEP) |
Clipped output |
| Each heat sink temperature |
Shutdown 105°C |
| Overvoltage Shutdown |
229 VAC / 440 VAC |
| Undervoltage Shutdown |
187 VAC / 360 VAC |
| Status Indicators (front panel) |
LEDs indicate a status of Run, Ready or Standby, and Fault, Over Temp, Over Voltage, and Over Load conditions |
| Controls (front panel) |
Soft Touch Switches |
Run (Enable), Stop and Reset functions |
| Controls (back panel) |
AC Mains Switch and Circuit Breaker |
Dual-function power switch and circuit breaker; rating: 30A for 208 volts or 15A for 400 volts. Turn off and then back on to reset. |
| Connectors (back panel) |
Power Connection |
NEMA-style locking receptacle; matching AC connector also included |
| Signal Output |
4-position terminal barrier block (OUTPUT/COMMON/ SAMPLED COMMON/CHASSIS GROUND); resistor between SAMPLED COMMON and CHASSIS GROUND terminals is a 2.7-ohm, 2W, 5%, metal-oxide resistor |
| Signal Input |
User-selectable unbalanced BNC or balanced Barrier Strip |
| Interlock I/O Connection: |
25-pin D connector provides for remote monitoring and control functions |
| Power Requirements |
Three-phase, 208 VAC ±10%, 47-60 Hz, 30 Amp AC service; (400 VAC ±10%, 15 Amp service model available) |
| Thermal Requirements |
Operating Temperature |
+10°C to +50°C (+50°F to +122°F). Maximum output power de-rated above 30° C (86°F). |
| Storage |
-30°C to +85°C (-22°F to +185°F) |
| Humidity |
70% or less, non-condensing |
| Physical Characteristics |
Dimensions |
19“ L x 12.25“ H x 22.8“ D (48.3 cm L x 31.1 cm H x 57.9 cm D). |
| Cooling |
Forced air cooling from front to back through removable filters via four 100 CFM fans. No space is required between rack-mounted amplifiers. Air filters are removable from the rear via one fastener per side and may be eliminated if cabinet filtration is provided. |
| Airflow |
600CFM |
| Weight |
153 lbs (69 kg) |
| Shipping Weight |
158 lbs (71.7 kg) |
![](javascript:addcart({"pid":915,"pname":"Rohde & Schwarz BBL200-series Broadband Amplifier 9 kHz - 225 MHz up to 10kW","image":"/uploads/2019/04/rs_bba200.png"})){kind=link}
![](javascript:addcart({"pid":914,"pname":"Rohde & Schwarz BBA150-series Broadband Amplifiers 4 kHz - 6 GHz up to 3000W","image":"/uploads/2019/04/rs_bba150.png"})){kind=link}
![](javascript:addcart({"pid":913,"pname":"Rohde & Schwarz BBA130-series Broadband Amplifiers 80 MHz - 6 GHz up to 4200W","image":"/uploads/2019/04/rs_bba130.png"})){kind=link}
![](javascript:addcart({"pid":41,"pname":"AE Techron 7700-series EMC Amplifiers DC - 30 kHz, 5 - 20kW","image":"/uploads/2019/02/ae_techron_7700-series.png"})){kind=link}
![](javascript:addcart({"pid":40,"pname":"AE Techron 7220-series EMC Amplifiers DC - 1 MHz 1000W","image":"/uploads/2019/02/ae_techron_7220-series.png"})){kind=link}
![](javascript:addcart({"pid":39,"pname":"AE Techron 7136 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7136.png"})){kind=link}
![](javascript:addcart({"pid":38,"pname":"AE Techron 7114 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7114.png"})){kind=link}
![](javascript:addcart({"pid":36,"pname":"AE Techron 7100-series High-Speed AC/DC Amplifiers","image":"/uploads/2019/02/ae_techron_7100-series.png"})){kind=link}
![](javascript:addcart({"pid":1409,"pname":"Teseq CBA 1G-1200B Broadband Amplifier 80 MHz - 1 GHz 1200W","image":"/uploads/2018/01/Image_Placeholder.png"})){kind=link}