| Performance |
| Testing was done at 100 Hz. Continuous DC power levels are lower. See DC Specifications chart for test conditions |
| Frequency Response |
DC - 300 kHz (1 watt): +1.0 to -2.0 dB |
| 8-Ohm Power Response (continuous duty) |
| DC to 60 kHz |
± 140 Vpk |
| DC to 200 kHz |
± 65 Vpk |
| DC to 350 kHz |
± 45 Vpk |
| Slew Rate |
75 V/µSec |
| Residual Noise |
| 10 Hz to 300 kHz |
950 µV (0.95 mV) |
| 10 Hz to 80 kHz |
300 µV (0.3 mV) |
| Signal-to-Noise Ratio |
| 10 Hz - 30 kHz |
-113 dB |
| 10 Hz - 80 kHz |
-106.6 dB |
| 10 Hz - 500 kHz |
-99.9 dB |
| Unit to Unit Phase Error |
±0.1 degrees at 60 Hz |
| THD (DC - 30 kHz) |
less than 0.1% |
| DC Offset |
Less than ±5 mV |
| DC Drift |
Less than ±1.5mV |
| Output Impedance |
5.3 mOhm in Series with 0.95 µH |
| Phase Response (10 Hz - 10 kHz) |
±5 degrees plus 600 nsec propagation delay |
| Input Characteristics |
| Balanced with ground |
Three terminal barrier block connector, 20k ohm differential |
| Unbalanced |
BNC connector, 10k ohm single ended |
| Gain, Voltage Mode |
20 volts/volt; Current Mode: 5 amperes/volt |
| Gain Linearity (over input signal, from 0.2V to 5V) |
0.15% |
| Max Input Voltage |
±10V, balanced or unbalanced |
| Common Mode Rejection |
-58 dB with 5 V input |
| Display, Control, Status, I/O |
| Front Panel LED Displays indicate |
Ready, Standby, Fault, Over Temp, Over Voltage, Overload |
| Soft Touch Switches for |
Run, Stop, Reset |
| Gain Control, when enabled |
Voltage gain adjustable from 20 to 0 |
| On/Off Breaker |
| Back Panel Power Connection |
25 Amp IEC (with retention latch) |
| Signal Output |
+/Common/Sampled Common |
| Signal Input |
User Selectable BNC or Barrier Strip Balanced |
| Communication Capabilities |
| Current Monitor |
± 1 V / 5 A ± 1% |
| Voltage Monitor |
± 1 V / 1 V ± 1% |
| Reporting |
System Fault, Over Temp, Over Voltage, Over Load |
| Remote Control via Interlock Connector |
Blanking control, Force to Standby, Reset after a fault |
| Physical Characteristics |
| Chassis |
The Amplifier is designed for standalone or rack mounted operation. The Chassis is black aluminum with a powder coat finish. The unit occupies two EIA 19-inch-wide units. |
| Weight |
41 lbs. (18.6 kg), Shipping 51 lbs. (23.2 kg) |
| Dimensions |
19“ x 22.75“ x 3.5“ (48.3 cm x 57.8 cm x 8.9 cm) |
![](javascript:addcart({"pid":915,"pname":"Rohde & Schwarz BBL200-series Broadband Amplifier 9 kHz - 225 MHz up to 10kW","image":"/uploads/2019/04/rs_bba200.png"})){kind=link}
![](javascript:addcart({"pid":914,"pname":"Rohde & Schwarz BBA150-series Broadband Amplifiers 4 kHz - 6 GHz up to 3000W","image":"/uploads/2019/04/rs_bba150.png"})){kind=link}
![](javascript:addcart({"pid":913,"pname":"Rohde & Schwarz BBA130-series Broadband Amplifiers 80 MHz - 6 GHz up to 4200W","image":"/uploads/2019/04/rs_bba130.png"})){kind=link}
![](javascript:addcart({"pid":41,"pname":"AE Techron 7700-series EMC Amplifiers DC - 30 kHz, 5 - 20kW","image":"/uploads/2019/02/ae_techron_7700-series.png"})){kind=link}
![](javascript:addcart({"pid":40,"pname":"AE Techron 7220-series EMC Amplifiers DC - 1 MHz 1000W","image":"/uploads/2019/02/ae_techron_7220-series.png"})){kind=link}
![](javascript:addcart({"pid":39,"pname":"AE Techron 7136 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7136.png"})){kind=link}
![](javascript:addcart({"pid":38,"pname":"AE Techron 7114 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7114.png"})){kind=link}
![](javascript:addcart({"pid":36,"pname":"AE Techron 7100-series High-Speed AC/DC Amplifiers","image":"/uploads/2019/02/ae_techron_7100-series.png"})){kind=link}