Carrier frequency

Range

10 kHz to 2700 MHz

Resolution

0.01 Hz

Accuracy

Same as that of the reference oscillator

Internal reference oscillator*1

Frequency: 10 MHz

Start-up characteristics: After 30 minutes of operation: ≤1 x 10–7/day, after 60 minutes of operation: ≤5 x 10–8/day, Aging rate: After 24 hours of operation: ≤2 x 10–8/day,

Temperature characteristics: ±5 x 10–8/day, (0˚ to 50˚C)

External reference signal input

10 MHz, TTL Level, BNC connector on rear panel

Reference signal output

10 MHz, TTL Level, BNC connector on rear panel

Switching time

≤10 ms (time from last command until frequency has stabilized to within ±500 Hz of set frequency, during remote operation)

Output

Range

–143 to +23 dBm

Units

dBm, dBµV, V, mV, µV (Terminated and open voltages are selectable for dBµV, V, mV or µV.)

Resolution

0.1 dB

Frequency response

±0.5 dB referred to 0 dBm (<1280 MHz), ±1 dB referred to 0 dBm (≥1280 MHz)

Accuracy

Frequency Output level

10 kHz to <1280 MHz

≥1280 MHz

+17.1 to +23 dBm

–

–

+15.1 to +17 dBm

±1 dB

–

–122.9 to +15 dBm

±1 dB

±2 dB

–132.9 to –123 dBm

±3 dB

±4 dB

–143 to –133 dBm

–

–

Impedance

50 Ω, N-type connector

VSWR: ≤1.5 (<1280 MHz, ≤–3 dBm), ≤1.8 (≥1280 MHz, ≤–3 dBm)

Switching time

Time from last command until output level is stabilized, during remote operation:≤25 ms (at LEVEL NORMAL mode)

≤80 ms (when setting level is crossing over –59 dBm, at LEVEL NORMAL mode)

≤5 ms (at LEVEL CONTINUOUS mode)

Interference radiation

≤1 µV (Value is voltage terminated with 50 Ω load, measured 25 mm from front panel with a two-turn 25 mm diameter loop antenna.) Except sweep mode

10 kHz to 2700 MHz

Resolution

0.01 Hz

Accuracy

Same as that of the reference oscillator

Internal reference oscillator*1

Frequency: 10 MHz

Start-up characteristics: After 30 minutes of operation: ≤1 x 10–7/day, after 60 minutes of operation: ≤5 x 10–8/day, Aging rate: After 24 hours of operation: ≤2 x 10–8/day,

Temperature characteristics: ±5 x 10–8/day, (0˚ to 50˚C)

External reference signal input

10 MHz, TTL Level, BNC connector on rear panel

Reference signal output

10 MHz, TTL Level, BNC connector on rear panel

Switching time

≤10 ms (time from last command until frequency has stabilized to within ±500 Hz of set frequency, during remote operation)

–143 to +23 dBm

Units

dBm, dBµV, V, mV, µV (Terminated and open voltages are selectable for dBµV, V, mV or µV.)

Resolution

0.1 dB

Frequency response

±0.5 dB referred to 0 dBm (<1280 MHz), ±1 dB referred to 0 dBm (≥1280 MHz)

Accuracy

Frequency Output level

10 kHz to <1280 MHz

≥1280 MHz

+17.1 to +23 dBm

–

–

+15.1 to +17 dBm

±1 dB

–

–122.9 to +15 dBm

±1 dB

±2 dB

–132.9 to –123 dBm

±3 dB

±4 dB

–143 to –133 dBm

–

–

Impedance

50 Ω, N-type connector

VSWR: ≤1.5 (<1280 MHz, ≤–3 dBm), ≤1.8 (≥1280 MHz, ≤–3 dBm)

Switching time

Time from last command until output level is stabilized, during remote operation:≤25 ms (at LEVEL NORMAL mode)

≤80 ms (when setting level is crossing over –59 dBm, at LEVEL NORMAL mode)

≤5 ms (at LEVEL CONTINUOUS mode)

Interference radiation

≤1 µV (Value is voltage terminated with 50 Ω load, measured 25 mm from front panel with a two-turn 25 mm diameter loop antenna.) Except sweep mode

Input level: Approx. 2 Vp-p/600 Ω

Input impedance: Nominal 600 Ω

Distortion

≤1% (internal 1 kHz, 5 rad modulation)

400 Hz, 1 kHz (fixed oscillator)

0.1 Hz to 100 kHz (variable oscillator)

DC voltage signals equivalent peak values of internal modulating sine wave can be applied as a modulating signal using the SPECIAL FUNCTION.

Resolution

0.1 Hz

Frequency accuracy

100 ppm

Distortion

≤0.03% (fixed, 400 Hz and 1 kHz), ≤0.3% (variable, 20 Hz to 50 kHz)

1000 carrier frequencies (store/recall)

Function memory

100 panel settings (store recall)

Carrier frequency, output level, AF frequency

Sweep time

0.1 ms to 600 s, 0.01 ms resolution (minimum time depends on the switching time of each function.)

Marker

One movable marker

Sweep signal output

Staircase (saw-tooth waveform), Start point: 0 V, Stop point: 10 V

Modulation signal is output when modulating. Output level: Approx. 2 Vp-p/600 Ω

Simultaneous modulation

Simultaneous modulation is possible in combinations shown below.

Relative value display

Carrier frequency, output level

Continuously variable output level mode

Continuously variable within a ±10 dB range of the set level Step size: 0.1 dB

Trigger function

Previously programmed operation procedure can be started by a trigger input through its input terminal (on rear panel, BNC connector, TTL level). Maximum program steps for triggered operation: 99 steps

Memory backup

Last settings are stored when power is turned off.

GPIB

Interface function: SH1, AH1, T5, L3, TE0, LE0, SR1, RL1, PP0, DC1, DT1, C0

Reverse power

Maximum reverse input power: 50 W (<1000 MHz), 25 W (≥1000 MHz), ±DC 50 V

Operating temperature

0˚ to 50˚C

Power

*7Vac +10%, 48 to 63 Hz, ≤270 VA

–15

Dimensions and mass

426 (W) x 177 (H) x 451 (D) mm, ≤32 kg

EMC*8

EN55011: 1991, Group 1, Class A

EN50082-1: 1992

Safety

EN61010-1:1993 (Installation Category II (Pollution Degree II)