|
POWER (fundamental), CW, @ OUTPUT CONNECTOR
|
|
Nominal
|
225 watts
|
|
Minimum
|
200 watts
|
|
Linear @ 1 dB Compression
|
50 watts minimum
|
|
FLATNESS
|
± 10 dB maximum
|
|
FREQUENCY RESPONSE
|
26.5 - 40 GHz instantaneously
|
|
INPUT FOR RATED OUTPUT
|
1.0 milliwatt maximum
|
|
GAIN (at maximum setting)
|
53 dB minimum
|
|
GAIN ADJUSTMENT (continuous range)
|
35 dB minimum
|
|
INPUT IMPEDANCE
|
50 ohms, VSWR 2.0:1 maximum
|
|
OUTPUT IMPEDANCE
|
50 ohms, VSWR 2.5:1 typical
|
|
MISMATCH TOLERANCE
|
Output power foldback protection at reflected power exceeding 40 watts. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. May oscillate with unshielded open due to coupling to input. Should not be tested with connector off.
|
|
MODULATION CAPABILITY
|
Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal. AM peak envelope power limited to specified power.
|
|
VIDEO PULSE CAPABILITY
|
|
Pulse Width
|
0.1 microseconds min
|
|
Pulse Rate (PRF)
|
10 kHz max
|
|
Duty Cycle
|
Some restrictions apply. Contact AR with application requirements.
|
|
RF Rise and Fall
|
100 ns max (10% to 90%)
|
|
Delay
|
500 ns max from pulse input to RF90%
|
|
Pulse width distortion
|
200 ns max (50% points of output pulse width compared to 50% points of input pulse width)
|
|
Noise Power Density, (pulse off)
|
Minus 140 dBm/Hz (typical)
|
|
Pulse Off Isolation
|
80 dB minimum, 90 dB typical
|
|
Pulse Input
|
TTL Level, 50 Ohm nominal termination, high level enables RF when video pulsing mode is selected.
|
|
NOISE POWER DENSITY
|
Minus 70 dBm/Hz (maximum)
|
|
Minus 75 dBm/Hz (typical)
|
|
HARMONIC DISTORTION
|
Minus 20 dBc maximum
|
|
Minus 30 dBc typical
|
|
PRIMARY POWER
|
190-260 VAC, 50/60 Hz single phase, 3 kVA maximum
|
|
CONNECTORS
|
|
RF input
|
Type K female on rear panel
|
|
RF output
|
Type WR-28 waveguide flange on rear panel
|
|
RF output sample ports
|
Type K female on rear panel
|
|
GPIB
|
IEEE-488 on rear panel
|
|
Interlock
|
DB-15 female on rear panel
|
|
Video
|
BNC female on rear panel
|
|
COOLING
|
Forced air (self contained fans), air entry and exit in rear
|
|
WEIGHT(approximate)
|
91 kg, 200 lbs
|
|
SIZE (W x H x D)
|
50.3 x 43 x 81 cm, 19.8 x 17 x 32 in.
|
![](javascript:addcart({"pid":914,"pname":"Rohde & Schwarz BBA150-series Broadband Amplifiers 4 kHz - 6 GHz up to 3000W","image":"/uploads/2019/04/rs_bba150.png"})){kind=link}
![](javascript:addcart({"pid":913,"pname":"Rohde & Schwarz BBA130-series Broadband Amplifiers 80 MHz - 6 GHz up to 4200W","image":"/uploads/2019/04/rs_bba130.png"})){kind=link}
![](javascript:addcart({"pid":40,"pname":"AE Techron 7220-series EMC Amplifiers DC - 1 MHz 1000W","image":"/uploads/2019/02/ae_techron_7220-series.png"})){kind=link}
![](javascript:addcart({"pid":39,"pname":"AE Techron 7136 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7136.png"})){kind=link}
![](javascript:addcart({"pid":38,"pname":"AE Techron 7114 High-speed AC/DC Amplifier","image":"/uploads/2019/02/ae_techron_7114.png"})){kind=link}
![](javascript:addcart({"pid":36,"pname":"AE Techron 7100-series High-Speed AC/DC Amplifiers","image":"/uploads/2019/02/ae_techron_7100-series.png"})){kind=link}
![](javascript:addcart({"pid":1416,"pname":"Teseq CBA 6G-120B Broadband Amplifier 1.8 GHz - 6 GHz 120W","image":"/uploads/2018/01/teseq_cba_6g-120b.png"})){kind=link}
![](javascript:addcart({"pid":1415,"pname":"Teseq CBA 6G-080B Broadband Amplifier 1.8 GHz - 6 GHz 80W","image":"/uploads/2018/01/teseq_cba_6g-080b.png"})){kind=link}
![](javascript:addcart({"pid":1414,"pname":"Teseq CBA 6G-040B Broadband Amplifier 1.8 GHz - 6 GHz 40W","image":"/uploads/2018/01/teseq_cba_6g-040b.png"})){kind=link}
![](javascript:addcart({"pid":1413,"pname":"Teseq CBA 3G-500B Broadband Amplifier 800 MHz - 3.1 GHz 500W","image":"/uploads/2018/01/Image_Placeholder.png"})){kind=link}
![](javascript:addcart({"pid":1412,"pname":"Teseq CBA 3G-300B Broadband Amplifier 800 MHz - 3.1 GHz 300W","image":"/uploads/2018/01/teseq_cba_3g-300b.png"})){kind=link}